u Key Features

Ø Integrated design: Al-in-one box

Integrating solar controller, power supply, IoT, network communications, PoE, and intelligent O&M into one box.

Ø Wireless installation: 4G/5G, Solar

Flexible to meet some special place where without power cable and optical fiber cable archived.

Ø Smart solar: Integrated solar controller

Remote monitoring for status of solar panel and battery. And control the battery charge and discharge.

Ø Intelligent O&M: Management Software

Real time monitoring and remote operation and maintenance.

Ø Environmental-friendly: Solar power and energy saving:

Making full use of natural energy, reducing environmental pollution and the dependence on traditional energy.

Ø High protection: Real industrial design

IP55 protection and rugged galvanized sheet encloser, voltage and current protection, Surge lightning protection, stable and reliable operation in hard environment.

u Functions

Intelligent Box Management

Ø Support intelligent temperature control, automatic fan control through temperature setting.

Ø Supports mains monitoring and mains voltage and current display; automatically collects overvoltage, undervoltage, and overcurrent alarm information, and remotely controls the switch to automatic reclosing.

Ø Support SPD status monitoring through teleindication inspection.

Ø Support temperature and humidity detect and parameter display.

Ø Support box door on/off status detection.

Ø Supports linkage between lighting and door, door open, lighting on; door close, lighting off.

Ø Support water inlet detection and auto report alarms.

Power Supply Management

Ø Support 4*DC12V power supply, single channel control, can remotely turned on/off the power, supports automatic over-current and short-circuit protection and alarm reporting.

Ø Support 1xDC24V power supply, can remotely turned on/off the power, supports automatic over-current and short-circuit protection and alarm reporting.

Ø Support 1xAC24V power supply, can remotely turned on/off the power, supports automatic over-current and short-circuit protection and alarm reporting.

Serial Port and Switch Quantity Management

Ø Support 2x 485/232 serial port, 4x DI/DO switch quantity.

Ø Support remotely turn on/off the serial port, switch quantity, and detect and display the status.

Ø Support serial port TX, RX traffic detection.

Ø Supports serial port baud rate, start bit, check bit, stop bit, flow control, as well as tcpip, port number and other Ethernet encapsulation content configuration to enable serial port data transparent transmission.

Ø Supports indicator lights to indicate the connection status of the serial port and the switch quantity.

Ø Supports protocol interfacing of devices external connected to the serial port(Customization)

Battery Management

Ø Support battery charging detection.

Ø Support battery discharging detection.

Ø Support battery overcharge protection.

Ø Low temperature protection, charging/discharging stops when the temperature is below the lower limit.

Ø High temperature protection, charging/discharging stops when the temperature is higher than the upper limit.

Switching Network Management

Ø Support Ethernet interfaces management, can remotely turn on/off the interfaces.

Ø Support MTU setting, ensure stable and reliable transmission of large data frames.

Ø Support flow control and automatically adjust the occurrence rate.

Ø Support VLAN.

Ø Support MAC address whitelist, secure access authentication.

Ø Support port traffic statistics.

Ø Support PoE management and query and display the parameter of PoE power supply voltage, current and power. Port 1-2 support IEEE802.3bt 90W.  Port 3-4 support remote 24VPoE/ 48VPoE mode setting. Port 5-8 support IEEE802.3af/at protocol auto identification.

4G Network Management

Ø Support remote viewing of 4G status, such as the acquired address, module frequency band, signal status, uplink and downlink traffic.

Ø Support network priority setting: 4G priority/wired interface priority

Ø Supports both business transmission and data management.

Ø Support manual modification of APN information.

Ø Support SIM card presence detection.

Solar Management

Ø Support reading and displaying the voltage, current and power of solar panels.

Ø Supports collecting the battery's min/max voltage, min/max charging/discharging current, max/min charging/discharging power, charging/discharging ampere-hours, power generation and power consumption on the day.

Ø Supports reading device operation days, over-discharge times, and full charge times.

Ø Supports battery reverse connection protection, battery low temperature protection (stop charging/discharging when the temperature is lower than the lower limit of charging/discharging), battery high temperature protection (stop charging/discharging when the temperature is higher than the upper limit of charging/discharging), and overcharge protection.

Ø Support fault alarm reports, such as: battery (lead-acid) cannot be detected, solar panel reverse connection, solar panel operating point overvoltage, photovoltaic input overvoltage, photovoltaic input power is too large, load power is too large or load overcurrent, load short circuit, undervoltage, battery overvoltage, battery overdischarge, etc.

System Management

Ø Support username and password management.

Ø Support software and hardware version viewing

Ø Support remote upgrade of firmware and configuration.

Ø Support remote restart.

Ø Support factory setting.

Ø Support NTP.

Application

Ø Widely applied to security monitoring, forest fire prevention, smart agriculture, environmental monitoring, oil, electricity, water conservancy, geological disaster prevention, scenic spots and various unattended environments.